Click to View Larger Image(s)
Get 6 months financing on orders of $99 or more when you pay with Bill Me Later through PayPal at our Checkout Page.
SLP Harmonic Balancer/Underdrive Pulley, 1997-10 LS1/LS6/LS2/LS3 Corvette/2008-09 L76 Pontiac G8/2009 GXP w/Bolt
Our Price $211.95
ASP Underdrive Pulley (SFI Approved) 25% Harmonic Dampner Crank
Our Price $261.40
Total Reviews for this product: 0
(Be the first to comment about this product)
showed up two weeks later in a beat up box did not have any mounts on them like shown in the picture so They don't stay Aligned the headers went perfect but did not have the mounts the rest of the exhaust does not stay aligned because there is no Mounts very happy with them not recommend them
gear and intake
LG Motorsports Long Tube Headers 1-7/8 for 2010-11 Camaro Cats Xpipe Muffler and Tips
No problems ordering and shipped fast. I tried a lot of companies and this is the only 3" full exhaust I had found for 5th gen. Install was fairly easy even without instructions. Take it from me look at the X pipe closely...there is a right and left side to it and it will go in backwards with out much effort. When it goes in correctly it is a lot easier to line up. The cats are not easily removed if you want to install off road pipe after about 100 miles. Takes some effort to get them off. I had to drop the whole exhaust to get them off As far as the sound. I like it. It is a real deep rumble that I have not heard on other 5th gens. It is not a loud obnoxious wake the neighbors similar to the Borla ATAK. You can even leave the car on through a drive through. Sounds like a V8 when you are in the throttle though. throttle response is very good too even with the bigger tubed headers. Over all I recommend and am very pleased
2012 SS Auto Long Tubes, tune, 3" exhaust (2.9 Whipple, Cam, lifters, and fuel Pump shipped today)
LG 2010-11 Camaro Short Shift Stick
I purchased this and never got any shipping status, even after asking for it. The part arrived wrapped in paper and in a big box. No instructions. The threads were cut M-14, not M-16 as advertised. I found a local machinist with a lathe who cut the threads to 1/2-20 and then I installed the shifter per a competitors instructions off the web, adjusting as needed. Difficult getting the small seal back in on top of the plastic 'bearing' that goes over the bottom pivot ball. The rubber boot over the bottom of the shifter was a real pain. Be patient and clean your hands before working with this boot as the grease on your fingers will make it very difficult. I installed a Hurst pistol grip knob and managed to use the chrome boot piece from the bottom of the factory shifter knob to finish the look. The boot leather just wire-ties to it and the jam nut for 1/2-20 fit inside it. Had I known, I could have just removed it from the factory knob and not cut the zip tie off. The shifter now shifts rock steady and has a much better throw distance and feel. There is some vibration thru the shifter now, but not bad. While I had difficulties all the way thru this install, the result seems to be worth the effort. I like the look of my setup better than the other choices I've seen available. The extra machining and the fee I incurred for their wrong advertising/machining was very distressing. I suggest you check this on yours before installing it, and return it if wrong. I expected more of a 'retail' package, rather than a sweat and pray bare-bones version. Beware...
Stock 2010 SS2 Camaro LS3
See More Reviews on LG Motorsports Parts
SLP Cold-Air Package, 1997-00 Corvette FloPac
SPEC Clutch Stage 1 - Chevrolet Corvette 1997-2004 5.7L LS-1, LS-6
B&B Bullet Exhaust with Quad Tips Corvette C5 1997-04
SPEC Clutch Stage 3 - Chevrolet Corvette 1997-2004 5.7L LS-1, LS-6
SLP Cold Air Induction, 1997-00 C-5 Corvette 'Blackwing'
Corsa: Corvette C5 (includes Z06) 1997-04 XO-Pipe [Crossover Pipe]